Primacoustic TriPad Mic Stand Isolators Set of 3 Foams

TriPad (set of three) is a tripod microphone stand isolator designed to reduce disruptive resonance and noise from the studio floor, stage or drum riser from entering the microphone. By decoupling the mic stand from the floor, the TriPad can significantly reduce the resonance created by drums, bass, toe tapping and foot-falls. Fits popular tripod mic stands, and made from high-density open cell foam with a cut-out that slips onto the leg of a tripod and stays attached. TriPads come in a set of three with their own protective storage container.

The TriPad features high density open cell foam that has been modified for added stiffness so that the microphone stand will not sway. This is cut into an attractive disc shape, drilled to a precise angle and then cut two more times to create the design.

The mic stand leg slips into the slot and once in place stays there making it easy to move the sand around the studio without having to reposition it each time. With less resonance entering the microphone, you will enjoy a more accurate sound and better results

• Extra stiff, high density open cell foam construction
• Easy to mount design fi ts most tripod mic stands
• Innovative slotted design keeps isolation pads in place
• Comes in handy storage case
• Eliminates resonance from fl oor and footstep noise
• Improves the sound of the recording
• Reduces time required to mast or EQ out problems
• Very cost effective
• Quick - easy to use design fi ts most mic stands
• Sturdy foam with low form factor will not cause mic to sway
• It looks good on the mic stand

SKB Cases 3SKB-R12U20W 20" Deep 12U Rolling Roto Shock Rack Flightcase

Rolling Shockmount SKB Case series 3SKB-R12U20W incorporates a recessed TSA trigger latches and low profile injection molded pull handle. The molded design provides extra stiffness in the lids and sides while also allowing the racks to stack securely together.

Features

• TSA latches
• Threaded steel rails
• Rear rails
• Built-in wheels
• Shock and water resistant
• Low profile pull handle

• Interior Width 19.00 in 48.26 cm
• Interior Height 21.00 in 53.34 cm
• Carton Length 29.00 in 73.66 cm
• Carton Width 31.00 in 78.74 cm
• Carton Depth 31.00 in 78.74 cm
• Rack Space Units Total 12 12
• Rack Depth Rail to Rail 20.00 in 50.80 cm
• Rack Depth Front Rail to Back Lid 22.25 in 56.52 cm
• Lid Depth 2.25 in 5.72 cm
• Shipping Weight TBA TBA
• Product Weight 67.95 lb 30.82 kg

Primacoustic TelePad Iphone 4 Holder for Microphone Stand TelePad-4 fits iPhones 4

Primacoustic TelePad is a unique mounting device for the Apple™ iPhone™ and Touch™ that makes it easy to position an iPhone on a mic stand for easy viewing and hands free use.

TelePad is a truly unique device designed for the popular Apple™ iPhone™ to allow the on-stage musician to position this ‘application-rich marvel’ right on the microphone stand so that it can be used as a teleprompter for lyrics, song chords, charts, metronome, backing tracks, playback and set list.

The design begins with a custom molded cradle that snugly fits around the iPhone without interfering with the microphone and switches. A spring loaded retainer clip lets you release the iPhone quickly for in-between set phone calls and messaging. The slide-on the cradle attaches to the mic stand clamp where a ball joint allows the phone to be rotated and angled for optimal viewing.

A 3-way adjustable mic stand clamp includes a rubberized ribbed lining that lets you snug the unit around a wide range of pipe sizes. This allows the TelePad to mount on the stand, boom or various attachments like drum stands. To expand functionality, the TelePad comes with a series of self-adhesive foam inserts you can use to accommodate smaller devices like the iPod™ Touch™.

Made from high impact molded plastic, the TelePad is easily mounted on a mic stand or boom attachment with the adjustable clamp. Once ready, the iPhone slides and locks into place and the cradle can be rotated 360º and or adjusted to the desired angle for viewing. The TelePad come with extra padding to fit slightly smaller phones or devices like the Apple Touch™ MP3 player.

With over 250,000 applications already in the market, the iPhone will surely find more uses. This surely means that the TelePad will find a home on film sets, remote broadcast trucks and other places where microphone stands, recording and media is employed.

Two TelePads are now available. The TelePad-3 fits iPhones 2G, 3G, 3GS and the iPod Touch 1G, 2G and 3G. The TelePad-4 fits the iPhone 4. Made from high impact polymers, the TelePad combines durability with functionality and will surely deliver years of on-stage enjoyment!

• Holds an iPhone on a mic stand for easy viewing
• Use iPhone ‘live’ as teleprompter, tuner, metronome…
• Adjustable clamp for all mic stand and boom sizes
• Quick release to keep your iPhone safe between sets

TelePad is a wonderful device designed to hold your iPhone or iPod Touch on a microphone or drum stand. Using the TelePad allows you to set a reasonable hands-free viewing angle while also allowing quick removal of the phone so that it does not get "borrowed" between sets!

The clamp is opened simply with a thumb screw and placed around a tubular stand such as a microphone or drum stand. The clamp's adjustable design accommodates stands up to one inch in diameter and the rubber lining provides a snug "finger tight" fit so no tools are needed.

A ball joint allows your iPhone to be viewed in portrait or landscape modes and angled for the best view. A locking ring tightens around the ball joint to prevent droop, even during a long two hour set. The phone cradle slides onto the ball joint's receiver so you can remove your phone without having to readjust the clamp and viewing angle.

Duracell Procell Size 9V / MN1604 Pack of 10 batteries BP9V

Duracell Procell Size 9V - MN1604Alkaline-Manganese Dioxide Battery10 batteries per packNominal Voltage 9VNominal Internal Impedance . 1700 m-ohm @ 1kHzAverage Weight . 45gm (1.6oz)Volume 22.8cm3 (1..39in3)Terminals Miniature SnapOperating T

First-AV.co.uk RG 58 Coax 50 Ohm RG Cable Black 4.95mm CACRG58

RG 58 B/UInner Conductor - 19/0.18mmDielectric - Foam PEBraid - T CUSheathing Material - PVCColour - BlackDiameter - 4.95mmCharacteristic Impedance - 50 Ohm
Price Per 100m

Syntax - Valentini Syntax Male Contact 16 COSM16

Syntax Male Contact 16

Neutrik Adaptor XLR Female to BNC Socket NA2FBNC Neutrik ATNA2FBNC

NA2FBNCNeutrik XLR-female to BNC socketWired according to IEC 268-12Pin 1 and 3: connected to groundPriced per connectorBox quantity: 25

Penn Elcom Wood Credenza Rack 8U 450MM Deep RCZ8R450

Beech effect wood laminate rack. 450mm deep and pre assembled. Optional Wall Mount Bracket available. Smoked doors NOT included (sold separately).

Ideal for use in offices, board rooms & churches. Available in sizes from 1U to 12U.

First-AV.co.uk 1U Rack Panel Steel Formed Louver Vented HA1UVL

1U Rack Panel Steel Formed Louver Vented

Neutrik XLR 3 Pin Male Black Shell Disassembled NC3MXX-BAG-D Neutrik CONC3MXXBAGD

NC3MXX-BAGD
Disassembled bulk pack available only in box quantities
3 pole male cable connector with black metal housing and silver contacts
The next generation of the worldwide-accepted standard of XLR cable connector.
Male connector with improved locking recess without window, more stringent housing increases durability
Internal thread on shell is well protected against any damage.
Rated current per contact: 16 A
Rated voltage: 50 V
Dielectric strength: 1.5 kV dc
Cable O.D: 3.5 - 8.0 mm
Wire size: max. 2.5 mm
Wiring: Solder contacts
Shell plating: Black chromium
Packing information: Box quantity = 100

First-AV.co.uk Mic Multicore Cable 2 Pair AES-EBU Black for DMX & Analogue caunc02

This premium quality Multicore cable (manufactured in Germany) combines flexibility and high level audio performance.
Applications
Microphone and Line level analogue balanced Audio Cable for touring and installation

Mechanical Specification
Conductor Stranded copper wire 18x0.10mm=0.14mm AWG 26 bare
Insulation Foam-Skin PE (02YS)
Twisting 2 cores to a pair (2 pairs)
Pair shield Alu/PVC foil metal inside
Drain wire Stranded copper tin plated 7 x 0.16mm= 0.14mm2 AWG 26
Sheath PVC colour grey
Jacket Soft PVC
Colour Black
Diameter 8.50mm + - 0.25mm

Technical Data
Conductor resistance max 138Ohm/km at 20 degrees centigrade
Insulation resistance min 100MOhm x km at 20 degrees centigrade
Capacitance C/C approx 40pF/m @1kHz
C/S approx 95pF/m @1kHz
Impedance approx 105 ohm @ 1Mhz
Operating voltage max 50-75 V AC/DC
Temperature range -20 to + 70 Centigrade

Neutrik XLR 5 Pin Female Chassis DLX Tapped Holes NC5FD-LX-M3 Neutrik CONC5FDLXM3

NC5FD-LX-M3
5 pole female receptacle, solder cups, Nickel housing, silver contacts, M3 mounting holes
The DLX series features a compact all metal housing with an ingenious duplex ground contact, which offers excellent RF protection and shielding. It is the ideal match for mating with Neutriks EMC XLR cable connector.
All metal housing offers best overall RF protection and electromagnetic shielding
New duplex ground contact for excellent contact integrity between chassis and cable connector
Unique cage type female contact on 3 pole version increases conductivity and reduces wear on the mated male contact
Female contact incorporates a solder barrier to prevent solder running into the contact mating area
Larger solder contacts for easier termination
Optional connection to easily join pin1 to chassis ground
D-style housing provides installation compatibility with industry standard D mounting dimensions

Ultimax Single Bar Goal Post Complete Kit 2.5M STUP6

Ultimax Singel Bar Goal Post Complete Kit 2.5M

For use with Ultimate DJ Stands

Electro-Voice Q66 Q Series Power Amplifier, 2 x 600W

Electro-Voice Q series amplifiers offer a package of reliable high output power, high efficiency and legendary pro audio performance. They are the premium choice as system drive for a variety of mobile and club sound systems like e.g. ZX, Tour-X and Phoenix loudspeaker families.

Comprehensive protection system - protection against overheating, overload, short circuit, HF and DC

Patented LPN filter - switchable frequency and phase response correction of connected loudspeakers

• Designed for House of Worship, Pro Music, and other applications.
• Up to 2 x 1200W into 2 ohms
• XLR pass-though input connections
• The NL4 connection on output A also carries output B on pins +/- 2 to allow easy connection to bi-amped loudspeakers
• Switchable LPN filter extra tonal fundamentals and “kick” with a protective low-cut for 12” or 15” loudspeakers without additional subwoofers
• Class-AB design
• Three-stage front-to-rear-fans
• Complete protection package
• Classic EV amplifier dynamic headroom for real-world music and applications
• Built-in dynamic limiters

Ceiling Speaker B404A Stereo

A ceiling mount speaker that provides both left and right stereo channels from a single point, whilst maintaining channel separation. The speaker has dual tweeters combined with a dual voice coil, woofer to deliver a full, rich sound. Ideal for installation in small rooms.

• Ceiling speaker White 6 ½ inch
• Dual Directional Tweeter
• 8 Ohms
• Sensitivity 89dB
• 60W rms
• 120W peak
• 60hz-20Khz
• Push Terminal Connections
• Cut out 193mm
• Mounting Depth 85mm from flange
• Back to front of speaker 92mm

Open Tower Rack System

The Open Tower Rack System allows for maximum air flow to rack mount equipment. Available in 24U, 35U and 43U sizes and a depth of 510mm/20". The rack system comes in individual flat pack items to be assembled on site.

Each rack system includes front and rear rack rail, 4 pairs of side supports, bottom and top units and adjustable height feet. Fixing screws are also included with the rack system.

Heavy duty castors are available as an optional extra.

Technical Information

• Colour: Black
• Depth: 510mm
• Units (rack): 24U, 35U, 43U, 16U
• Weight: 15kg / 33.07 lbs

SKU: Open Rack

First-AV.co.uk Electrical Insulation Tape PVC Orange 19mm x 33M BS3924 HCTE33OR

PVC Electrical Tape Orange

A self-extinguishing conformable PVC orange electrical insulation tape fully conforms to BS3924 and EN60454/1 specification.

Roll Length: 33M
Roll Width: 19mm
Total Thickness: 0.13mm
Backing Thickness: 0.11mm
Peel Adhesion (steel): 1.8 N/cm
Tensile Strength: 16.5 N/cm
Elongation at Break: 160%
Temperature Range: -5 to +70oC
Dielectric Strength: 6.0 KV
Shelf Life: 12 months in original packaging stored in cool dry conditions
Priced per roll
Packaging: Shrink-wrapped in packs of 8, with 6 packs to an outer box of 48

APPLICATIONS
Wire and cable insulation
Loom harnessing in electronics and automotive industries
Colour coding and identification
Masking during chemical process plating
Retaining protective pads and socks in contact sports

First-AV.co.uk WF125 Coax Foam Filled Digital Cable RG 7 Black 8.1mm CACWF125

WF 125Belden Ref - RG 7Inner Conductor - 1.25mm CUDielectric - Foam PEDiameter over Dielectric - 5.72mmScreen - CU FoilBraid and Coverage CU - CU 40%Outer Conductor OD - 6.6mmSheathing Material - PEDiameter over Sheath - 8.1mmColour - BlackWeig
Price Per 100m

Neutrik Loaded 8 Way Stage Box SBLOA8

8 Way stage box loaded with Neutrik NC3FDLX-BAG connectors. Loaded box is numbered 1-8. Includes blanking plate (with 20mm hole) to house cable Gland. Stage Box can be fitted with 25 Pin Multipin (25 Pin connector not included).

Stage Boxes can be customised on request using company logos, phone numbers and email addresses.

Neutrik Bantam Miniature Jack Plug 3 Pole Black NP3TT-P-B Neutrik CONP3TTPB

NP3TT-P-B
Redesign of NP3TT-1
4.4 mm Bantam plug
Solder termination for Tip + Ring
Crimp termination for Screen with standard RG58 crimp tool
Black plastic housing
Nickel contacts
Dielectric strength: 1000kVdc
Rated voltage: 50V
Cable O.D: 4 - 4.8mm
Wire size: 24AWG
4.4 mm (0.173in) tiny telephone plug bantam type featuring 3 conductors and HEX crimp of Screen with a standard RG58 crimp tool
Ideal use with TT patch panels
Priced per connector
Box quantity: 100

Penn Elcom 19in Rack Enclosure Floor 600 x 800mm 42U inc Doors Black RMEMS6842

RMEMS6842 - Floor Standing Network Cabinet

Rack enclosure is supplied flat packed and includes; front and rear doors, side panels, front and rear rack rail, castors and feet.

Available sizes: 22U, 32U and 42U.
Material: 2mm steel
Colour: black power coat
Width: 600mm
Depth: 800mm
Height: 42U

Deluxe free standing network cabinet with a static load capacity of 500kg
Adjustable feet plus castors for convenient positioning and stability
Network cabinets are designed to bay together
Toughened glass front door with vented sides and spring loaded push and turn locking system
Steel rear door
Quick release design for both front and rear doors
Removable side panels with spring latch.
Perforated top for ventilation and cable entry knockouts
Adjustable depth 11 gauge front rack rails

Supplied with:
M6 Pan head screws and cage nuts.
4 x jacking feet
4 x heavy duty castors
Front glass door with vented border, spring lock and blue ornament strip
Steel rear door and lock
Side panels with fast open bolt
Top and bottom with cable entrance cover

Neutrik Jack Skt Stereo Switched Half Nose and chassis ground NRJ6HH-1 Neutrik CONRJ6HH1

NRJ6HH-1
1/4in stereo jack, switched, half threaded nose, sleeve contact/front panel connection
Horizontal PCB panel mount jack featuring high board packing density by mounting on 15.88 mm (0.625 inch) minimum centers in rows or arrays. Mounting hardware must be ordered separately.
Features & Benefits
High boarded packing densities
A retentions spring ensures optimum grip on inserted plugs, avoiding the chance of lost connection
Mounting nuts available in various styles